Generic selectors
Exact matches only
Search in title
Search in content

Centrifugal Pump Basics: How It Works

PSG

Centrifugal Pump Basics: How It Works

By: PSG

In this edition of the Centrifugal Pump Minute, James Farley, Senior Director of Product Management for Griswold, goes through how a centrifugal pump is constructed and illustrates how the pump operates.

Now without a little bit of history, I wanted to go through how a centrifugal pump is constructed. There are some variations and differences this particular one is going to be for a close-coupled end suction pump. There are different centrifugal pump designs. We’ll talk about those a little bit, but they all, in the end, perform very similarly. In this particular pump, you have suction, there’s a flange on the end of the pump where the fluid would enter the pump, and then there’s a discharge. On this one, it is a radial discharge pump. There’s a flange going off to the side where the flow is going to exit the pump. Essentially, you’re going to have fluid going in at a lower pressure. Then, you’re going to have in centrifugal pump terms head you’ll have fluid exiting the pump at a higher head.

Now to look at more of the internals and what’s actually happening inside the pump. We’re going to cut away part of the casing so you can see internal to this pump. Then we’re going to take a portion of the impeller, which is called the front shroud, and we’re going to make that transparent so you can actually see the vein geometry of the impeller sitting behind that shroud. What you see here is now a cutaway from the center of the pump. When a pump is operating, the impeller is going to be rotating. Notice the direction of the arrows and the kind of curvature of the impeller veins. Some people have a perception that the vein of the impeller would rotate, at least from this image, in a clockwise direction. That’s not the case, the impeller has to rotate in a counterclockwise direction.

The veins of the impeller flicker or throw the fluid and through kinematic energy. The impeller is going to rotate. It’s going to be driven by some sort of a rotating shaft. That shaft has to be powered by some sort of an engine or drive. It could be an electric motor, a diesel drive, a hydraulic motor, or a variety of things. When that impeller is rotating, it’s going to start to accelerate the fluid. This energizes the fluid. That energy creates what’s considered head in the fluid. That’s increased pressure inside the fluid. That fluid that was in the impeller is now going with higher energy through centrifugal force. It’s going to end up getting thrown radially outside of the impeller into the casing. That energy accelerates that fluid, causing it to go outward radially into the casing geometry. That geometry is called a volute geometry that collects that fluid and starts directing it. The fluid is then going to the casing then is going to collect the fluid is going to slow down the fluid. It’s actually through Bernoulli’s principle that the fluid needs to slow down to generate a higher head. That fluid is going to collect and get sent out of the discharge of the case. It will essentially have a very high head as the fluid exits through the discharge nozzle. To replenish the fluid that’s been pushed out of the casing we need to be pulling more fluid into the suction of the pump and so as the pump is operating. The fluid moves into the impeller because you have a low-pressure region generated at the inlet of the impeller. That low pressure is what will start to suck that fluid into the impeller or the pump and therefore continue the pumping action of the centrifugal pump. Again you’re going to have fluid that moves from the impeller and into this low-pressure zone at the impeller eye and then that’s going to pull that fluid through and around in the centrifugal pump. By doing this you’re getting a continuous flow that’s going through the centrifugal pump and that one of the advantages of a central pump is that the flow is very stable steady, you don’t have pulsation in the discharge or on the suction line when you’re operating a centrifugal pump.

Watch more Centrifugal Pump Minute videos.

Related Articles

Related Whitepapers

Electrical Energy Savings using Anti-Stagnation Valves

The City of Hamilton is a port city situated at the west end of Lake Ontario in the Canadian province of Ontario. It is the…

No More Headaches – Low Maintenance Pumping Vegetables

The vegetable and potato industry, almost always processing in an environment with a very high humidity, working with flexible process installations, multi-language staff, and always…

Cutter Pump Solutions to Plugging Problems

In creating the cutter option to deal with wastewater ragging and fouling, an important concern was to keep efficiency as high as possible. Two designs…

Reliable Pumps for Oil and Gas Processing with No Dynamic Seals or Packing to Leak or Replace

Compact, Seal-less Pumps for Reliable Operation and Long Service Life With more than 40 years of experience serving the industry, including many of the major…

Comments

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Sign up for our Newsletter!


By submitting this form, you are consenting to receive marketing emails from: Empowering Pumps & Equipment, 2205-C 7th Street, Tuscaloosa, AL, 35401, http://www.empoweringpumps.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact