Dredge Components

The 10-inch booster pump is designed with centrifugal singles suction volute having a 12 inch diameter suction and is arranged for 10-inch inside diameter suction pipe. The 10-inch pump is mounted on a steel base. It is powered by a John Deere 6090 diesel engine rated at 325bhp @2200RPM.. The dredge pump is a GIW model LCC-M250-660. Booster is reported to be in very good condition. It was purchased for a specific job, it was never used again. Very low hours and excellent condition. Location: State of California, USA

Non-clog design for high solids industrial pumping applications. Min flow of 450 gal/min and a max flow of 2000 gal/min. Has a capacity of 150-200 yd3/hr. Only used on one job. Very low hours and in excellent condition.  Location: State of California, USA

Non-clog design for high solids industrial pumping applications. Min flow of 1200 gal/min and a max flow of 5000 gal/min. Has a capacity of 300-350 yd3/hr. Only used on one job. Very low hours and in excellent condition.  Location: State of California, USA

Pump comes outfitted with a jet ring, water supply pump, 2 saddles and a control box, 50 ft of electrical cord and 250 ft of 10 inch fixed HDPE pipe. Location: State of Oregon, USA

Comes outfitted with a hydraulically driven mechanical agitators, 250 ft of 10 inch fixed HDPE pipe, includes hydraulic power unit and associated controls. Requires misc. riggings and shackles to operate.  Location: State of Oregon, USA

GIW 12" x 10" Underwater Pump  Location: State of Nebraska, USA

Metso J36 12" x 12" Pump. Location: State of Nebraska, USA

Metso 8x6 slurry pump with drive and 50 hp motor.  Location: State of Nebraska, USA

Dredge works 65 HP cutter drive with pump and end ladder. The cutterhead has a 14-inch suction.  Location: State of Nebraska, USA

Twin Disc MG 518-1; 2.47 to 1 reduction; sn 3 x 3918; rated 750 hp. Has been inspected and is in very good condition. Location: State of Nebraska, USA

IMS Razor Tooth Weedmaster Cutterhead bolts directly to the IMS Model 5012 LP Versi-Dredge in place of the standard cutterhead. The Weedmaster attachment (8-feet) chops the weeds into small pieces - 3-5 inch (76-127mm) - to allow pumping into geotextile bags for decomposing or pumps them to the shore, up to 1km away, using the vegetation dredge pump.   Location: Canada

The boosters have only been used on one project. Impeller and volute cast from high chrome Gasite iron. Discharge diameter is 10-in, suction diameter is 12-in and sphere passage is 5-in. Price for each pump. One of the pumps has about 1950 hours, the other about 2000 hours.  Location: State of Florida, USA

Built in 2018 at Dragflow in Italy. Hydraulic motor. Pump has been used for only 300 hours. Suitable for bentonite water, slurry water, sand-water, salt sand water, etc. Location: Netherlands

Ellicott 670 Booster pump is in good working condition. The Cat C18 engine has 2,035 runtime hours. Location: State of West Virginia, USA

Brand new GIW Impeller 14x36 IN 3M 2C4.5 for a dredge pump. The rotation direction is clockwise from the shaft side. The impeller weights 526.17 kg (1160 lbs). Location: Netherlands

This 18-inch (457 mm) Booster Pump is mounted on floating pontoons. The pontoons measure 10 m x 6 m. The booster has been used on one job and run around 1500 hours. It is in good working condition and well maintained. The slurry capacity is 3500 m3/hr and has a discharge distance of 2000 m. Location: Turkey

This 18-inch (457 mm) Booster Pump is mounted on floating pontoons. The pontoons measure 10 m x 6 m. The booster has been used on one job and run around 1500 hours. It is in good working condition and well maintained. The slurry capacity is 3500 m3/hr and has a discharge distance of 2000 m. Location: Turkey

This 10-inch (254 mm), 600 hp Booster Pump. The pump is skid mounted and has 2,000 hours. The engine and gearbox are in good condition. Pump is in very good condition. Location: Portugal

This 12-inch (305) mm, 715 hp Booster Pump was built in 2002. The pump is skid mounted and has 1,500 LOW hours with oil samples. The booster is diesel powered and V-belt driven. Location: State of Illinois, USA

This 10-inch Ellicott 370 Pump was built in 2009. It is a complete pump and transmission (bearing housing and shaft). The wear plate and impeller are 25% worn, the transmission has new bearings, seals and a cooler. Location: Georgia

This listing is for a 20-inch Booster Barge that was built in Holland by IHC. It was last run about one year ago. Location: Adriatic Sea

This is a 6 x 6-inch Booster Pump with a Marathon electric motor. Location: State of Louisiana, USA

This 14-inch "Dragflow" Submersible Hydraulic Driven Pump was built in 2011. Location: Russia

The engine on this 6-inch Booster pump has been completely rebuilt and has only 2 test hours. The Dredge pump is in excellent condition, the skid unbolts from the wheel base so that the pump can be barge mounted easily. The skid is designed to contain oil in case of an oil leak. Location: State of Florida, USA

There are three complete assembled pump packages, including skids, pump motors and VFDs. There is one assembled pump package, including skids, pump motors and VFD, and a spare motor and pump is available with the 3-unit package for additional cost. Location: State of California, USA